RFC137


RFC index | STD index | BCP index | FYI index
Plain text | gzipped plain text | A4 postscript | A4 postscript, 2 up | A4 postscript, 4 up
Network Working Group T. C. O'Sullivan Request for Comments: 137 Raytheon NIC 6714 30 April 1971 TELNET Protocol This is a request for comment and is being distributed in advance of the Atlantic City meetings for review and comment prior to or during discussions on TELNET in preparation for issuing an official document. It is also being distributed so that selected installations planning to implement early versions of TELNET will have a common basis for such implementation. The proposed document is the result of the work of the committee. It represents a TELNET protocol felt to be adequate for initial implementation. A few recent suggestions by committee members and others have been incorporated where even though not thoroughly cleared with all members, the chairman felt that they clarified the protocol or would tend to simplify implementation but not substantially change the agreed-upon approach. Readers are referenced to the following previous releases of information: 1. Conventions for Using an IBM 2741 Terminal or a User Console for Access to Network Server HOSTS Joel Winett, RFC 110 (NIC #5809) 2. Level III Server Protocol for the Lincoln Laboratory 360/67 HOST Joel Winett, RFC 109 (NIC #5808) 3. First Cut at a Proposed TELNET Protocol J. Melvin, D. Watson, RFC 97 (NIC #5740) 4. ASCII Format for Network Interchange V. Cerf, RFC 20 (NIC# 4722) Another RFC will be distributed prior to the Atlantic City Meetings containing many of the arguments supporting the proposal. O'Sullivan [Page 1]
RFC 137 TELNET Protocol April 1971 TELNET PROTOCOL A Proposed Document T. O'Sullivan for the TELNET Committee Will Crowther BBN Bob Long SDC John Melvin SRI-ARC Bob Metcalf Harvard Ed Meyer MAC Tom O'Sullivan (Chairman) Raytheon Joel Winett MIT-LL O'Sullivan [Page 2]
RFC 137 TELNET Protocol April 1971 TELNET is a third-level protocol, the function of which is to make a terminal (or process) at a using site appear to the system or a process at a serving site as logically equivalent to a terminal "directly" connected to the serving site. In performing this function, the protocol attempts to minimize the amount of information each HOST must keep about the characteristics of other HOSTS. Definitions Protocol Levels (see Figure 1) Level 1 HOST-IMP protocol specified by BBN in NIC 5735, Specifications for the Interconnection of a HOST, and an IMP (BBN Report 1822) Level 2 HOST-HOST protocol performed by NCPs as described in Document Number 1 (NIC 5413) and subsequent amendments, see RFC 107 (NIC #5806) One view of the NCP's function is that it takes information from the net and routes it to receiving processes via mechanisms internal to each HOST; conversely, processes use the NCP, via internal system calls, to have information routed to other processes in the net (via the other processes' NCPs). Level 3 (see Figure 2) Level 3 is, by definition, the place to which and from which the NCP communicates internally in its own host. This level may be equivalent to the user process level in some systems, but this may not be the case in all systems. In using sites, the TELNET process operates at this level. In serving sites, the TELNET server operates at this level. Initial Connection Protocol (ICP) An agreed-upon sequence of level 3 exchanges between two processes which is, in general, used to synchronize the dialogue between the processes, e.g., RFC 80 (NIC #5608) #1. O'Sullivan [Page 3]
RFC 137 TELNET Protocol April 1971 Serving Site The HOST into which the TELNET process is directing the user's keyboard input and from which the TELNET process is receiving control information and data effecting the user's terminal. At the serving site, a TELNET server is executing. Using Site The HOST in which the TELNET process is executing. Sending Site The HOST transmitting data, could be either using site or serving site. Receiving Site Converse of sending site. User The person or process "driving" the TELNET process. In providing services the TELNET protocol will use established network conventions, specifically the Network Control Program, and Initial Connection Protocol referenced in the above definitions. The TELNET protocol provides for a Network Virtual Terminal (NVT) through which users may transmit and receive data over connections between the using site and the serving site. The code of the NVT will be full ASCII. The seven-bit code will be transmitted in eight-bit bytes, the high order bit set to zero. It will be the responsibility of the using site to provide its users with a means of producing all 128 ASCII codes, as well as a selected set of special TELNET control signals (see Figure 3). O'Sullivan [Page 4]
RFC 137 TELNET Protocol April 1971 The ASCII character ESC will be employed by the user as an escape signal indicating that the next character(s) has special meaning. The meaning assigned to escape code will be serving site defined and therefore may not be consistant across the network. It will be the responsibility of the serving site to specify for users how the NVT code will be used to represent the codes normally generated by a local terminal. The serving sites specification of this representation is expected, where reasonable, to map on a one- for-one basis for ASCII graphics and controls that are provided through local terminals. The serving site will also specify how the escape conventions will be interpreted by the system. The end of a line will be represented in the NVT as carriage return followed by line feed. The protocol assumes that at initially the serving site will not provide any echo to the using site. Each TELNET control signal for which code must be sent over the connection will be represented in the NVT by an eight-bit code, with the high order bit set to one. Following are the special codes established to date. (U) indicates that in most implementations the user would be expected to have the ability to signal the TELNET process from his terminal to initiate the code. Code X'A0' Source: Both Sites (U) Meaning: A DATA TYPE[1] signal indicating that code will be transmitted by NVT, i.e., using the seven-bit ASCII conventions. Code X'80' Source: Using Site (U) Meaning: Order using site NCP to send an INS and insert X'80' in data stream. Code X'81' Source: Using Site (U) Meaning: Break or Attention O'Sullivan [Page 5]
RFC 137 TELNET Protocol April 1971 Code X'82' Source: Serving System Meaning: Reverse Break Code X'83' Source: Both Sites Meaning: I Echo Code X'84' Source: Both Sites Meaning: You Echo Code X'85' Reserved Code X'86' Reserved Code X'87' Source: Both Sites Meaning: This site has not implemented the following control code. Code X'88' Source: Both Sites Meaning: [2]Return to control mode, i.e. next byte will be a control signal, possible a new DATA TYPE. Some special TELNET control signals are required to permit the user on some systems to send control information to the using site TELNET process. These do not require a corresponding control code for transmission. The local TELNET control signals are: 1. Transmit all data to this point. 2. Suppress transmission of end of line, send all other data. O'Sullivan [Page 6]
RFC 137 TELNET Protocol April 1971 Data is to be forwarded to the NCP for transmission as convenient, but at least at the end of line, end of line suppression, and transmit signals. If the normal line length of the sending site is greater than the allocation given by the receiving site, the sending sites TELNET process or TELNET server will be responsible for breaking the line into convenient lengths and turning them over to the NCP for transmission. This document will be revised as necessary to provide conventions for data types, in addition to the NVT ASCII type. Footnotes: [1] A one-byte DATA TYPE signal is sent as the first byte of data over a connection. A default is employed if the first byte over a connection has the high order bit set to zero, and it is assumed that the seven-bit ASCII NVT convention will be employed. After initial connection, the DATA TYPE may be changed (see code X'88'). Most implementations and applications may expect the DATA TYPES to be symmetrical at any point in time,(i.e. both using a serving site using the same DATA TYPE.). [2] A site receiving a DATA TYPE signal is to respond with a double X'88' if the new DATA TYPE is acceptable. O'Sullivan [Page 7]
RFC 137 TELNET Protocol April 1971 |<------- 32 ------->|<-8->|<-8->|<-- 16 -->|<-8->|<--- +--------------------+-----+-----+----------+-----+------------------ | leader | x |size | count | x | TEXT +--------------------+-----+-----+----------+-----+------------------ |<---- level 1 ---->| message leader |<------------------ level 2 ------------------>| message preamble level 3 |<- message text..--> Figure 1. Network Message on Link 2-31 Indicating Portions of Interest to Various Levels USING HOST Serving HOST -----------------------+ +---------------------- | | \ | | / \ -----------------| +-+ +-+ |-----------------/ \ NCP | |I| |I| | NCP / \ ^ <--->|M|---NETWORK--|M|<---> ^ / \ -----|-----+ | |P| |P| | +-----|-----/ \ v | | +-+ +-+ | | v / USER \ | | | | TELNET / USER PROCESSES, ) TELNET |--| |--|Protocol( PROCESS Sub <===> | | | |Routing<--->Sub Systems, / ^ | | | | ^^ \Systems ETC /-----|-----+ | | +----||-----\ETC / TTY v <---> Local Local <===> TTY vv \ / Handles | Terminals Terminals| Handles <===> /-----------------| |-----------------\ / | | \ | | -----------------------+ +---------------------- <---> Current TELNET paths <===> Candidate future TELNET paths Figure 2. Current and Candidate Future TELNET Paths O'Sullivan [Page 8]
RFC 137 TELNET Protocol April 1971 +---------------------------+----+----+----+----+----+----+----+----+ |\ b8 -> | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | | \ b7 -> | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | | \ b6 -> | 0 | 0 | 1 | 1 | 0 | 0 | 1 | 1 | |B \ b5 -> | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 | | I +---+---+---+---+------+----+----+----+----+----+----+----+----+ + T | b | b | b | b |\COL->| | | | | | | | | \ S| 4 | 3 | 2 | 1 | \ | | | | | | | | | \ | | | | | |\ | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | \ | | | | | | | | | v \ | | | | | | | | | \ | v | v | v | v |ROW \ | | | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 0 | 0 | 0 | 0 |NUL |DLE | SP | 0 | @ | P | \ | p | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 0 | 0 | 1 | 1 |SOH |DC1 | ! | 1 | A | Q | a | q | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 0 | 1 | 0 | 2 |STX |DC2 | " | 2 | B | R | b | r | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 0 | 1 | 1 | 3 |ETX |DC3 | # | 3 | C | S | c | s | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 1 | 0 | 0 | 4 |EOT |DC4 | $ | 4 | D | T | d | t | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 1 | 0 | 1 | 5 |ENQ |NAC | % | 5 | E | U | e | u | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 1 | 1 | 0 | 6 |ACK |SYN | & | 6 | F | V | f | v | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 1 | 1 | 1 | 7 |BEL |ETB | ' | 7 | G | W | g | w | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 0 | 0 | 0 | 8 | BS |CAN | ( | 8 | H | X | h | x | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 0 | 0 | 1 | 9 | HT | EM | ) | 9 | I | Y | i | y | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 0 | 1 | 0 | 10 | LF |SUB | * | : | J | Z | j | z | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 0 | 1 | 1 | 11 | VT |ESC | + | ; | K | [ | k | { | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 1 | 0 | 0 | 12 | FF | FS | , | < | L | \ | l | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 1 | 0 | 1 | 13 | CR | GS | - | = | M | ] | m | } | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 1 | 1 | 0 | 14 | S0 | RS | . | > | N | ^ | n | ~ | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 1 | 1 | 1 | 15 | S1 | US | / | ? | O | _ | o |DEL | +---+---+---+---+------+----+----+----+----+----+----+----+----+ Code Structure 8 7 6 5 4 3 2 1 --- --- --- --- --- --- --- --- --- --- O'Sullivan [Page 9]
RFC 137 TELNET Protocol April 1971 +---------------------------+----+----+----+----+----+----+----+----+ |\ b8 -> | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | | \ b7 -> | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | | \ b6 -> | 0 | 0 | 1 | 1 | 0 | 0 | 1 | 1 | |B \ b5 -> | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 | | I +---+---+---+---+------+----+----+----+----+----+----+----+----+ + T | b | b | b | b |\COL->| | | | | | | | | \ S| 4 | 3 | 2 | 1 | \ | | | | | | | | | \ | | | | | |\ | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | \ | | | | | | | | | v \ | | | | | | | | | \ | v | v | v | v |ROW \ | | | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 0 | 0 | 0 | 0 |'80'| |'A0'| | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 0 | 0 | 1 | 1 |'81'| | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 0 | 1 | 0 | 2 |'82'| | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 0 | 1 | 1 | 3 |'83'| | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 1 | 0 | 0 | 4 |'84'| | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 1 | 0 | 1 | 5 |'85'| | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 1 | 1 | 0 | 6 |'86'| | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 0 | 1 | 1 | 1 | 7 |'87'| | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 0 | 0 | 0 | 8 |'88'| | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 0 | 0 | 1 | 9 | | | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 0 | 1 | 0 | 10 | | | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 0 | 1 | 1 | 11 | | | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 1 | 0 | 0 | 12 | | | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 1 | 0 | 1 | 13 | | | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 1 | 1 | 0 | 14 | | | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ | 1 | 1 | 1 | 1 | 15 | | | | | | | | | +---+---+---+---+------+----+----+----+----+----+----+----+----+ 'XX' = HEX designation for codes assigned to TELNET Control Signals. Figure 3. Official Network Virtual Terminal Code O'Sullivan [Page 10]
RFC 137 TELNET Protocol April 1971 [This RFC was put into machine readable form for entry] [into the online RFC archives by Sergio Kleiman, 8/01] O'Sullivan [Page 11]